Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Westchester Homeowners
A missing or rusted-out cap is the most common reason a Westchester chimney starts failing from the inside. Rain runs straight down the flue, soaks the masonry, and works its way into the framing around the firebox. A cracked crown does the same damage more slowly, letting water pool on top of the chimney and seep into the brick below. We handle both, and we treat them as one job because they solve the same problem: keeping water out of a structure that was never meant to hold it.
Our technicians have up to 15 years of experience with caps and crowns, and we work with the same professional-grade product lines chimney engineers specify. We can usually get eyes on a failing cap or crown the same day you call. Reach us at (866) 490-9807 and we’ll book a visit, give you a flat-price quote before any work begins, and back the installation with a satisfaction guarantee.
What Our Chimney Cap & Crown Service Includes
Cap and crown work covers six distinct jobs. Some chimneys need one, some need two together, and a few need none of it. We’ll tell you which situation yours is after we’ve been on the roof.
Cap Installation
A chimney cap is the metal hood that sits over the flue opening, keeping rain, birds, and debris out while letting smoke escape. You need one if your flue is open at the top, if you’ve just had a liner installed, or if a home inspection flagged the opening as unprotected. We install caps sized to the exact flue dimensions, anchored into the crown rather than wedged in, so wind doesn’t walk them loose over a season.

Cap Replacement
A cap that’s rusted through, bent, or missing its mesh has stopped doing its job even though it’s still sitting up there. You need replacement when you see rust stains running down the chimney face, when the mesh is torn or sagging, or when the cap rattles in wind. We pull the old unit, inspect the crown underneath for damage the failing cap may have caused, and fit a new cap in the same visit.

Crown Repair
The crown is the concrete or mortar slab on top of the chimney that sheds water away from the brick. You need repair when you see cracks wider than a hairline, pieces flaking off, or a crown pulling away from the flue. We rebuild failed sections with a proper slope so water runs off instead of sitting, which is the whole point of the crown and the reason a flat or dished crown always fails early.

Crown Coating
Crown coating is a flexible sealant applied over a crown that’s sound but showing surface cracks. You need it when the crown is structurally intact but the surface has started to check and craze, which is the stage before real cracking begins. We prep the surface, apply a coating that moves with the concrete instead of cracking away from it, and get several more years out of a crown that doesn’t need replacing yet.
Multi-Flue Cap
A multi-flue cap is a single large hood that covers two or more flues sharing one chimney, common on older Westchester homes with a fireplace plus a furnace flue. You need one when separate caps sit unevenly, when flues are too close together for individual units, or when the existing setup lets water run between the flues. We build these to the actual footprint of your chimney top, not to a standard size, so the fit is right the first time.
Custom Cap
Some chimneys don’t take a stock cap: oversized flues, unusual shapes, or a top the homeowner wants to match the house. Custom caps are fabricated to your chimney’s exact measurements, in the metal and finish you choose. You need one when a standard cap won’t seat properly or when the chimney’s proportions call for something built for it. We measure on site and install once the piece is made.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We work with professional-tier chimney brands because the materials hold up differently than what you’ll find on a hardware store shelf. Gelco and Copperfield caps are built for longevity and proper fit, and we know how their units seat on a crown and where they tend to fail first. Olympia Chimney components show up in a lot of the multi-flue and custom work we do, and we’re familiar with how their sizing runs.
HeatShield is a resurfacing product rather than a cap or crown brand, but it matters here: when a crown repair uncovers a deteriorated flue tile underneath, HeatShield lets us resurface rather than jump straight to a full liner replacement. Whether you have Famco, Olympia, Gelco, or any other make, we can help. If your existing cap is a brand we haven’t named, that’s fine, the principles of a proper install don’t change.
If you’re comparing cap and crown work across providers, it helps to know what a full-scope Westchester chimney sweep and repair company actually covers, since cap and crown is only one part of a chimney’s water-shedding system.
Signs You Need Chimney Cap & Crown Right Now
- Water stains on the ceiling or chimney breast. Brown rings or damp patches near the chimney usually mean water is getting past the crown or a failed cap and soaking into the masonry. Left alone, that moisture reaches framing and drywall, and the repair grows beyond the chimney itself.
- Rust streaks or a rusted cap. Rust on the cap or streaks down the chimney face mean the metal has given out and water is passing through it. A cap that’s rusted through isn’t a cap anymore, it’s a screen door.
- Visible cracks in the crown. Cracks wider than a hairline, or pieces of concrete flaking off the top, let water sit against the brick instead of running away from it. That’s the mechanism behind spalling brick and, eventually, structural repair.
- Birds, squirrels, or debris in the firebox. An open or damaged flue top is an invitation. Nesting material and leaves in the flue don’t just smell, they restrict draft and create a fire hazard the next time you burn.
- Draft problems or smoke rolling back into the room. A cap installed at the wrong height or a crown that’s shifted can change how the chimney draws. If the fireplace worked before and doesn’t now, the top of the chimney is one of the first places we look.
Our Chimney Cap & Crown Process – Step by Step
- 1
Rooftop inspection. We get on the roof and look at the cap, crown, flue, and flashing together. Cap problems and crown problems often travel in pairs, and we want to see the whole top of the chimney before recommending anything.
- 2
Photo documentation. We photograph what we find and show you the images. If you’ve been told your crown is cracked or your cap is shot, you’ll see the evidence rather than take our word for it.
- 3
Written flat-price quote. You get a written quote that breaks out each item and the flat price for the job, agreed before anyone starts. If part of the work can safely wait, we’ll tell you that too. Nothing gets added later without your approval.
- 4
Installation with proper materials. Cap or crown work is only as good as the materials and the fit. We size caps to the flue, slope crowns for drainage, and use the same professional-grade products we’d specify on our own homes. No caulk-and-run fixes.
- 5
Final check and walkthrough. We test the installation, confirm the cap is secure and the crown drains, and walk you through what we did and how to spot problems early. You’ll know what to look for before the next rainy season.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Westchester?
Most chimney cap and crown work in Westchester falls into a few predictable ranges. A standard cap installation typically runs $250 – $550 depending on flue size and the metal you choose. Cap replacement sits around $200 – $450, since the old unit comes out and the crown underneath gets checked at the same time. Crown repair costs more because it’s masonry work: roughly $400 – $900 depending on how much of the crown needs rebuilding and how much slope has to be corrected. Crown coating, which only applies to a crown that’s still structurally sound, runs about $250 – $550. A multi-flue or custom cap is priced by the piece and typically runs $500 – $1,200 depending on the footprint and finish.
Those ranges shift with the height of the chimney, the condition of the crown underneath, and whether the cap needs custom fabrication. The way to avoid overpaying is simple: get a written estimate that itemizes each element, and ask whether anything can safely wait a season. Our estimates are free and come with photos of what we found, so you’re not comparing numbers in the dark. The written estimate sets the final price, and we don’t start until you’ve approved it.
Chimney Cap & Crown Near Westchester – Our Service Area
We work across the Westchester area, including Marina del Rey, Lennox, Ladera Heights, Inglewood, Culver City, View Park-Windsor Hills, Mar Vista, Del Aire, El Segundo, Hawthorne, and Venice. Dispatch runs Sunday through Friday, 7am to 7pm, and most nearby calls get scheduled the same day you reach us. If you’re close by, we can usually get a technician out to look at the chimney top quickly. Our chimney cap & crown page covers nearby work in more detail, and our chimney cap & crown page covers Lennox and the surrounding neighborhoods.
Serving Westchester, CA – Our Local Coverage Area
We serve Westchester and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Westchester
Chimney cap and crown work is the repair or installation of the two structures that keep water out of your chimney. The cap is the metal hood over the flue; the crown is the concrete slab on top of the chimney that sheds water away from the brick. Together they protect the masonry from the rain that causes most chimney damage in this area. It’s one of the highest-value repairs you can make on a chimney, because it prevents the expensive structural work that follows years of water intrusion.
Most cap installations and replacements take one to two hours, and crown repair typically takes half a day. Crown coating runs about two to three hours once the surface is prepped. Custom and multi-flue caps can take longer because the piece has to be fabricated to your chimney’s measurements first, then installed in a second visit. We’ll give you a realistic time window with your written quote.
Cap work typically runs $200 – $550, and crown repair runs $400 – $900 depending on how much needs rebuilding. Crown coating, which applies only when the crown is still sound, runs about $250 – $550. Custom and multi-flue caps run $500 – $1,200 because they’re made to measure rather than fitted from a stock size. Call (866) 490-9807 for an exact quote. Estimates are free.
Yes. We install and service the professional-tier lines chimney engineers specify: Gelco, Copperfield, Olympia Chimney, Famco, and HeatShield for flue resurfacing. That means we know how each brand’s caps seat and where they tend to wear, rather than learning on your chimney. If your existing equipment is a brand we haven’t named, we can still work with it. The principles of a proper installation don’t change from one maker to the next.
We can often schedule a same-day visit for Westchester calls, depending on how the day is booked. We answer 24/7, and crews are dispatched Sunday through Friday, 7am to 7pm. We’re closed Saturday. A call outside dispatch hours gets booked into the next opening. To reach us, call (866) 490-9807.
Our installations are backed by a satisfaction guarantee, and we stand behind the workmanship as well as the material. If something we installed isn’t performing the way it should, call us and we’ll come look at it. We’ll walk you through exactly what’s covered before you approve the quote, so there’s no ambiguity later. The same goes for any brand-specific product we install.
You don’t need to do much. Clear any vehicles or objects away from where a ladder needs to sit, and make sure we can access the roof area. If you have a fireplace or wood stove, don’t light a fire on the day of the visit, since we’ll be working around the flue. Let us know about any previous repairs or known issues, and we’ll factor them into the inspection.
Schedule Your Chimney Cap & Crown Service in Westchester Today
Water damage and draft problems don’t fix themselves, but most cap and crown work is straightforward once someone who knows chimneys takes a look. Book a free estimate with Westchester Chimney Sweep Pros and we’ll tell you what your chimney actually needs, and what it doesn’t. Call (866) 490-9807. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. No obligation, no pressure, just a clear answer.
Written by the team at Westchester Chimney Sweep Pros.